Dlinkap.local
Dlinkap.local login to Dlink extender setup and configuration. Change the settings of Dlink extender such as login credentials, wireless security settings, fix parental control, and many more after assessing http://dlinkap.local admin login panel. Enter your username and password on the login page and start configuring your Dlink WiFi range extender.
Dlinkap.local login
Dlinkap.local login allows the users to access the setup wizards. Before proceeding with the Dlink extender login and Dlink extender setup, plug your Dlink extender and router in the same room. You need to connect your computer to the Dlink WiFi range extender through an ethernet cable.


Access dlinkap.local admin page
Following are the steps to access dlinkap.local:
- Connect your device to the Dlink extender’s network and open a web browser.
- Enter dlinkap.local in the URL bar and tap on the enter button.
- On the Dlink extender login page, enter your username and password in the given field and tap on the login button.
Dlink Extender Setup
Dlink extender setup boosts the signal strength and eliminates the WiFi dead zones. You can easily manage the settings and configure the Dlink WiFi range extender through Dlink.local setup. There are two methods to install Dlink wireless extender:
- Web browser.
- WPS method.

Dlink.local Setup Through The Web Browser
Go through the below-mentioned steps complete the dlink.local setup via web browser:
- First and foremost, connect your Dlink WiFi range extender to the wall socket and turn it on.
- Now, grab an ethernet cable to connect your computer or laptop to the Dlink extender.
- After that, connect your device to the Dlink extender’s network and launch a web browser.
- Type dlinkap.local in the address bar of the web browser and press the enter key.
- On the Dlink extender login page, enter your username and password and tap on the login button.
- Select the setup option from the configuration page and proceed with the next step.
- After that, choose the “extend an existing wireless network” option and then select the wireless network you want to extend.
- Enter the password and tap on the Next button to proceed further.
- Then, modify the network SSID and type your extender’s network password.
Note: The password for the extender’s network and router should be different.
- Proceed with the on-screen instructions and tap on the finish button to complete the Dlink extender setup.
- Finally, you can connect your WiFi-enabled devices to the Dlink WiFi extender’s network.

Dlink.local Setup Through WPS Methods
Check out the following steps to set up the Dlink extender through the WPS button:
- Place your Dlink WiFi range extender and WiFi router in the same room and connect the extender to the power source.
- After that, press the WPS button on the extender and wait for the solid LED light.
- Now, press the WPS button on the router within two minutes after pressing the WPS button on the extender.
- A solid green LED light on the extender indicates that the extender is connected to the router successfully.
- Now, you can unplug the Dlink extender and place it in a new location halfway between the router and WiFi signal dead zone.
How to set up dlinkap.local in AP mode?
Following are the steps for dlinkap.local setup in AP mode:
- Go to the configuration page and tap on the AP option. After that, enter your network SSID, set the channel on auto mode, and modify the security mode to WPA2 or PSK.
- After that, enter the password and tap on the apply button.
- Then, select your WiFi network from the list of all available networks and enter the password for your wireless network.
- Select the name for repeater and tap on the apply button.
- Finally, you can connect your devices to the Dlink extender’s network.

Dlinkap.Local password change
The default username for the Dlink extender is admin, and the password is password. But the default Dlinkap local username password is very easy to crack. Go through the below-mentioned steps to change the dlinkap.local username and password:
- First of all, connect your Dlink extender to the wall socket and turn it on.
- Now, connect your computer or laptop to the extender's network and launch a web browser.
- In the address bar, enter dlinkap.local and press the enter key.
- Enter admin in the username box and password in the password box on the login page and tap on the login button.
- Then, select the wireless tab from the home page and go to the wireless security mode section.
- Enable the WPA2 option and tap on the “passphrase field” option
- After that, enter the new password twice in the given field and tap on the Save button to apply the changes.

Check the ethernet connection
To fix the dlinkap.local not working issue, make sure that the ethernet cable is connected correctly. Make sure that your Dlink router is connected to a working power outlet. If the power outlet is not working, then unplug your device and plug it in another socket.

Disable the antivirus program
Antivirus or malware programs can also interrupt the working of dlinkap.local. Therefore, disable the antivirus software and try to access the dlinkap.local web address.

Enter The Correct dlinkap.local Login Details
Make sure that you are entering the correct login details to access dlinkap.local. The default username for the Dlink extender is admin, and the password is password. If you have changed the passwords, then make sure that you are entering the new password.

Update Dlink Extender Firmware
Ensure that you are using the updated version of Dlink extender firmware because the updated firmware can cause login issues. Visit dlinkap.local to download the latest version of Dlink extender firmware.

Restart your Dlink extender
Disconnect your Dlink extender from the power source and router. Wait for a few seconds and then reconnect to the power source. Restart your computer as well. This will fix the dlinkap.local not working error.
Dlink Extender Reset
If the above-mentioned methods are not working, then reset your Dlink WiFi range extender to the factory default settings. To reset the extender, press the reset button on the extender for a few seconds and then release it. The Dlink extender will reboot itself and restore the factory default settings. Now, try to access the dlinkap.local admin panel and check if the issue is resolved or not.